DH3511 INOX 110V DryFan 45L Déshumidificateur déshydratant en acier inoxydable

Alimentation 110V 50 Hz pouvant être alimentée par un convertisseur 12V DC-110V AC ou par des transformateurs 220V à 110V, réarmement automatique en cas d'interruption de l'alimentation électrique. "Déshumidificateur commercial en acier inoxydable 316 à 4 trous ; extraction de l'eau de 45 litres maximum. Plage de fonctionnement de -20°C à 40°C de température ambiante maximale pour des applications de séchage en continu, avec une capacité de volume d'air de 380 m3/h (380 m3/h - extraction / 75 m3/h - régénération du flux d'air). Ventilateur très efficace, très silencieux et à faible consommation d'énergie pour une grande capacité d'extraction de l'humidité. 58dB Air de process en 125mm - Air de process en sortie 125mm - Air d'échappement 80mm - Air régénéré 80mm

SKU : DH3511-1 Catégories : Déshumidificateurs de , Déshumidificateurs de UE, Déshumidificateurs à UE, Déshumidificateurs à , Déshumidificateurs à Tags : ,
installer des déshumidificateurs déshumidificateurs par Ecor Pro
déshumidificateur télécharger le manuel d'utilisation déshumidificateurs par Ecor Pro
comparer nos produits déshumidificateurs par Ecor Pro


Ideal For Wind Turbines & Marine Applications.

45 litre Desiccant Dehumidifier 110V / 50Hz.

Autonome ou installé.

Industrial dehumidifier DH3511 stainless steel construction.Firstly, very small for its 45 litre capacity. Dries 24/7, even down to -20°C/-4°F. Works up to 40°C/104°F.

Stainless Steel Inside & OutSalt Resistant with 316 Stainless Steel

Able to be carried by one person and transported easily with removable carrying handles.Moreover, self-regulating energy usage that adapts to air pressure differences using always the right amount of power to dry effectively

Déshumidificateur à 4 trous

In addition, input process air is dust filtered & dried. Input air can be ducted in & out with a 125mm / 5″ duct. Wet air exhaust is 80mm / 3″ duct & Regen air input also 80mm / 3″.

Les recherches d'Ecor Pro montrent que le DH3511 sera quatre à sept fois plus rapide pour sécher les bâtiments à basse température qu'un déshumidificateur à compresseur traditionnel

Parties associées

Caractéristiques expliquées

Highly Compact – Small 45 Litre dehumidifier.Dust Filter – Furthermore, the desiccant industrial dehumidifier benefits from a simple reticulated dust filter in metal frame. Shakened clean or easily replaced. Prevents dust particles entering the unit and impeding performance.Easy Repair – Easy to remove cover. Easy access to replace cord sets or warn parts by a qualified persons quickly. Prolonging the lifetime of the DH35XX dehumidifier. Cord sets can be replaced in around 20 minutesOn Four Feet – Anti scratch plastic feet.Carrying Handle – Easy to carry by one person. Moreover, the handle can be removed if the product is being installed. Handles also protect the dehumidifier duct flanges if in transit.Humidistat Connection – Alternatively, it has no integral humidistat but one can be added very simply. Military standard connector is on the front of the unit. To add this use, the remote humidistat EPHUM220. This will turn the dehumidifier on and off automatically.

Parfait pour tout climat.

Duct Air-In & Out – The dehumidifier has all ducts fitted with flanges to allow ducting to be added with 125mm / 5″ hard or flexible ducting.Wet Air Exhaust – DH35XX has two internal fans compared to one in the DH25XX. Both do not produce water. The moisture is vented away allowing it to work in colder temperatures. Moisture is purged from the system by Regen air.“Four Hole System” –  Two inlets and two outlets. Dries pressure neutrally in certain spaces. The DH3511 can be used to dry a large fridge freezer, for instance.

Alimentation électrique - Alimentation 110V 50Hz.
Réinitialisation automatique - En cas d'interruption de l'alimentation électrique, le DH35XX continuera à fonctionner dès que le courant sera revenu. Parfait dans les endroits où l'alimentation électrique est "sale" et peut affecter d'autres produits à commande électronique.
All Metal Construction – All stainless steel inside and out. Designed for longevity.
4m / 12′ Power Cord – No need to join cables when placed for instance in crawl spaces or lofts in the home for example with commercial plug fitted.

Dehumidifier Installation



This is a 4-Hole dehumidifier meaning that there are 2 separate fans inside.  One for the Process-Air (Air that needs to be dried) and the Regen Air that is used to purge the wheel of moistures and is then vented away

Drying a water-damaged room has moved on from the days of lighting a fire and opening the doors and windows. The industry no longer leaves a dehumidifier in the middle of the flood-damaged room with a couple of air movers and hopes for the best, not least because it wastes expensive energy and because contractors are increasingly aware of the need to reduce both their carbon footprint and the time it takes to do the job.

Power availability also means more efficient products can be used on the power supply than more power hungry units.

With saving labour and making effective use of expensive assets increasingly important in a competitive market, focused or targeted drying is a good start, but as we move towards a more sustainable, cost-focused industry, it’s not enough.

Using tenting for target drying ensures the dehumidifier only dries the wet parts of the room and avoids drying unaffected areas, a process that can cause secondary damage by sucking too much moisture out of some of the materials in the rest of the room. In short, drying a whole room to remedy a flood in part of it is remarkably inefficient.

Targeted drying uses plastic sheeting to create a sealed chamber, or ‘tent’, around the wet area of the room, saving significant amounts of energy by not drying the 90% of the room that wasn’t wet in the first place - but even that approach is inefficient.

The inefficiency arises when the tent is fed from outside by the dry air from a desiccant (absorption) dehumidifier, the best choice when drying dense materials like brick or block walls.

As air is blown into the tent, the same volume of air must escape. This positive pressure system means that the drying air is taken from the whole room – as well as from outside if the windows are open. That makes the whole room part of the drying regime, with the dehumidifier forced to dry potentially damp air before putting it into the tent. If the air being fed in can’t be controlled, the drying can’t be controlled either.

The answer is to create a negative pressure system by moving the dehumidifier inside the tent, creating a controlled environment.

Let’s talk maths. In our positive system, a normal three port desiccant dehumidifier moving 150 cubic metres (5300 cft) per hour is probably generating   cubic metres (4200 cft) of dry air for drying and using 30 cubic metres (1000 cft) to dry its wheel. In a typical one cubic metre tent (35 cft) , the air is exchanged 120 times per hour, but if the tent is in a room with a total volume of 60 cubic metres (2100 cft), the air in the room outside the tent is recirculated twice, too – to no purpose.

In a negative system, the air in the tent is exchanged only 30 times but is recirculated 120 times per hour, each time becoming drier, significantly increasing the efficiency of the drying regime and reducing energy usage.

Taking this a step further, Ecor Pro’s four port DH3500/EPD200 and the EPD300 uses a separate air stream to dry its wheel, so it works at an equal pressure and air in the tent is not exchanged with the air in the room. The dehumidifier can be placed inside the tent and the ‘regen’ air to dry the wheel pumped into the tent and back out. Alternatively, the dehumidifier can be placed outside the tent and the air taken from the tent to the dehumidifier and back, which means the drying tent or chamber can be sealed around the ducts to give maximum efficiency.

Air recirculation 100%, air exchange 0%. That is efficient.

Moisture is "vented away".  No water is produced.  The moist air is vented to the outside or moved to another area that is vented. Most common installation.

Focussing the dry air gives faster drying times.  Example of "Positive Pressure" or forcing the dry air into areas it is needed

Recirculating the air to be dried gives a compound effect and gives faster drying.  This system is "Neutral Pressure" and is outside the room being dried.

Having the machine in the area being dried and recirculating the air is the most efficient way of drying.  This system is "Neutral Pressure" and is inside the room being dried.

Operating below zero and can operate in sealed rooms, 4-Hole allows even cold rooms and freezers to reduce moisture problems.

Poids 24.4 kg
Dimensions 73 × 41 × 47 cm
(L x l x H)-(poids)

24,82" x 13,86" x 13,58" - 45,19lbs



Extrait de Max


Alimentation / Prise / Longueur du cordon

1400W, 110V, 50Hz, 11,7A / Oui Industriel

Code barre

EAN 50602

Couleur / Matière

Acier inoxydable 316

Dimensions des conduits

80mm (3.0")-125mm (5")

Prêt pour la piscine


Humidistat Inside / Option Humidistat

Non / Oui

Poignée de transport / Conteneur d'eau / Longueur du cordon d'alimentation

Oui / Non / 4m

Vitesse des ventilateurs / Son

1 / 58dB

Température de fonctionnement

De moins 20°C à plus 40°C

Redémarrage par coupure de courant / fonctionne à partir d'un couvercle DC-AC

Oui / Oui

Débit d'air m3/hr

400 procédé / 125 échappement

Redémarrage après une coupure de courant


Travaux de la couverture DC-AC


Réservoir d'eau



Acier inoxydable 316



Vous avez récemment consulté...