DH3511 110V DryFan 45L Desiccant Dehumidifier

110V supply 50 Hz that can be run off a 12V DC-110V AC converters or 220V to 110V transformers, auto power reset in case of power supply interruption. “4-hole” technology commercial desiccant dehumidifier; water removal 45 litres maximum extraction. Operating range from -20?C up 40?C maximum room temperature for continuous drying applications, with 380 m3/hr air volume capacity (380 m3/hr – exhaust / 75m3/hr – regen air flow). Highly efficient, very quiet fan operation and yet low energy consumption in use for large moisture extraction capacity. 58dB Process air in 125mm – Process air out 125mm – Exhaust air 80mm – Regen air 80mm

instalar deshumidificadores deshumidificadores de Ecor Pro
deshumidificador descargar manual de usuario deshumidificadores por Ecor Pro
comparar nuestros productos deshumidificadores por Ecor Pro

NO SE PRODUCE AGUA. LA HUMEDAD SE VENTILA INCLUSO HACIA ARRIBA

Secador de inundación ideal. Restauración segura

45 Deshumidificador de Desecante de litro 110V / 50Hz

Libre o instalado

Industrial dehumidifier DH3511 steel construction with tough epoxy paint finish.Very small for its 45 litre capacity. Will dry 247 and dry even down to -20°C/-4°F. Can work up to 40°C/104°F.

Steel Inside & OutTough Enough Even for Hiring or Restoration

Can be carried by one person and transported easily with the carrying handles.Self regulating energy usage that adapts to air pressure differences using always the right amount of power to dry effectively

Deshumidificador de 4 agujeros

El aire de proceso de entrada es filtrado y secado por el polvo. El aire de entrada puede ser conducido dentro y fuera con un conducto de 125 mm / 5″. La salida de aire húmedo es de 80 mm / 3″ conducto y la entrada de aire Regen también 80 mm / 3″

La investigación de Ecor Pro muestra que el DH3511 será de cuatro a siete veces más rápido en el secado de edificios a bajas temperaturas que un deshumidificador de compresor tradicional

Partes asociadas

El DH3511 se utiliza con otros para secar el aparcamiento

Explicación de las características

Altamente compacto - Tal vez el deshumidificador de 45 litros más pequeño del mercado.

Dust Filter – Simple reticulated dust filter in metal frame. Shakened clean or easily replaced. Prevents dust particles entering the unit and impeding performance.
Fácil reparación - El mantenimiento y la eventual reparación han sido pensados con una cubierta fácil de quitar que permite un fácil acceso para reemplazar los juegos de cables o advertir a las partes por parte de una persona calificada rápidamente. Prolongando la vida útil del deshumidificador DH35XX. Los juegos de cables pueden ser reemplazados en unos 20 minutos
En Cuatro Pies - Pies de plástico anti arañazos.
Carrying Handle – Easy to carry by one person. Optional to remove handles. Handles also protect the dehumidifier duct flanges if in transit.
Humidistat Connection – There is no integral humidistat but one can be added very simply. A military standard connector is on the front of the unit. To add this use the remote humidistat EPHUM220.This will turn the dehumidifier on an off automatically.

Perfect for any climate.

Conducto de entrada y salida de aire - El deshumidificador tiene todos los conductos equipados con bridas para permitir que se añadan conductos con 125 mm / 5″ conductos duros o flexibles.

Wet Air Exhaust – The DH35XX has two internal fans compared to one in the DH25XX. Both do not produce water. Works in colder temperatures via vented away moisture. Regen air purges moisture from system.
“Four Hole System” – Two inlets and two outlets. Four hole system aids pressure neutral drying. Used to dry large fridge freezer, for instance.
Suministro de energía - Suministro de 110V 50Hz
Auto reset - Si hay una interrupción en el suministro de energía, el DH35XX continuará funcionando tan pronto como la energía haya sido devuelta. Perfecto en lugares donde hay una fuente de alimentación "sucia" que puede afectar a otros productos controlados electrónicamente.
Construcción de metal - Todo el metal con acabado de pintura epóxica tratado térmicamente para que sea resistente por dentro y por fuera. Diseñado para la longevidad.
4m / 12′ Cable de alimentación - no hay necesidad de unir los cables cuando se colocan, por ejemplo, en los espacios de descanso o en los lofts de la casa, por ejemplo.

Dehumidifier Installation

 

 

This is a 4-Hole dehumidifier meaning that there are 2 separate fans inside.  One for the Process-Air (Air that needs to be dried) and the Regen Air that is used to purge the wheel of moistures and is then vented away

Drying a water-damaged room has moved on from the days of lighting a fire and opening the doors and windows. The industry no longer leaves a dehumidifier in the middle of the flood-damaged room with a couple of air movers and hopes for the best, not least because it wastes expensive energy and because contractors are increasingly aware of the need to reduce both their carbon footprint and the time it takes to do the job.

Power availability also means more efficient products can be used on the power supply than more power hungry units.

With saving labour and making effective use of expensive assets increasingly important in a competitive market, focused or targeted drying is a good start, but as we move towards a more sustainable, cost-focused industry, it’s not enough.

Using tenting for target drying ensures the dehumidifier only dries the wet parts of the room and avoids drying unaffected areas, a process that can cause secondary damage by sucking too much moisture out of some of the materials in the rest of the room. In short, drying a whole room to remedy a flood in part of it is remarkably inefficient.

Targeted drying uses plastic sheeting to create a sealed chamber, or ‘tent’, around the wet area of the room, saving significant amounts of energy by not drying the 90% of the room that wasn’t wet in the first place - but even that approach is inefficient.

The inefficiency arises when the tent is fed from outside by the dry air from a desiccant (absorption) dehumidifier, the best choice when drying dense materials like brick or block walls.

As air is blown into the tent, the same volume of air must escape. This positive pressure system means that the drying air is taken from the whole room – as well as from outside if the windows are open. That makes the whole room part of the drying regime, with the dehumidifier forced to dry potentially damp air before putting it into the tent. If the air being fed in can’t be controlled, the drying can’t be controlled either.

The answer is to create a negative pressure system by moving the dehumidifier inside the tent, creating a controlled environment.

Let’s talk maths. In our positive system, a normal three port desiccant dehumidifier moving 150 cubic metres (5300 cft) per hour is probably generating   cubic metres (4200 cft) of dry air for drying and using 30 cubic metres (1000 cft) to dry its wheel. In a typical one cubic metre tent (35 cft) , the air is exchanged 120 times per hour, but if the tent is in a room with a total volume of 60 cubic metres (2100 cft), the air in the room outside the tent is recirculated twice, too – to no purpose.

In a negative system, the air in the tent is exchanged only 30 times but is recirculated 120 times per hour, each time becoming drier, significantly increasing the efficiency of the drying regime and reducing energy usage.

Taking this a step further, Ecor Pro’s four port DH3500/EPD200 and the EPD300 uses a separate air stream to dry its wheel, so it works at an equal pressure and air in the tent is not exchanged with the air in the room. The dehumidifier can be placed inside the tent and the ‘regen’ air to dry the wheel pumped into the tent and back out. Alternatively, the dehumidifier can be placed outside the tent and the air taken from the tent to the dehumidifier and back, which means the drying tent or chamber can be sealed around the ducts to give maximum efficiency.

Air recirculation 100%, air exchange 0%. That is efficient.

Moisture is "vented away".  No water is produced.  The moist air is vented to the outside or moved to another area that is vented. Most common installation.

Focussing the dry air gives faster drying times.  Example of "Positive Pressure" or forcing the dry air into areas it is needed

Recirculating the air to be dried gives a compound effect and gives faster drying.  This system is "Neutral Pressure" and is outside the room being dried.

Having the machine in the area being dried and recirculating the air is the most efficient way of drying.  This system is "Neutral Pressure" and is inside the room being dried.

Operating below zero and can operate in sealed rooms, 4-Hole allows even cold rooms and freezers to reduce moisture problems.

Peso 24.4 kg
Dimensiones 73 × 41 × 47 cm
(L x W x H)-(peso)

24.82" x 13.86" x 13.58" - 45.19lbs

Tecnología

Desecante

Extracto de Max

45L-95pt

Alimentación / enchufe / longitud del cable

1400W, 110V, 50Hz, 11.7A / Sí Industrial

Código de barras

EAN 5060224951187

Color / Material

Negro amarillo / pintura epoyada de acero suave

Tamaño de los conductos

80mm (3.0")-125mm (5")

Piscina lista

No

Humidistato en el interior / Opción de humidistato

No / Sí

Asa de transporte / contenedor de agua / cable de alimentación Longitud

Sí / No / 4m

Velocidades del ventilador / sonido

1 / 58dB

Temperatura de funcionamiento

Menos 20?C a más 40?C

Reinicio de la salida de energía / Funciona desde el cubrecorriente DC-AC

Sí / Sí

Flujo de aire m3/hr

400 proceso / 125 escape

Reinicio del apagado

Trabaja desde el DC-AC Coverter

Tanque de agua

No

Material

Acero suave recubierto de expoxy

Aprobación

CE

Recientemente has visto...